Sandpiper SPA40-E User Manual download pdf

spa105dl3sm Model SPA1½-E and SPA40-E Design Level 3 Page 1

WARREN RUPP, INC., A unit of IDEX Corporation • 800 N. Main Street • Manseld, OH 44902 USA • (419) 524-8388 Fax (419) 522-7867

OPERATING INSTRUCTIONS

THE PUMP: This pump is a totally enclosed, submersible dewatering unit. It is

easy connection to any 12 volt vehicle battery.

SWITCHING: The on-off switch is located on the power cord.

CONNECTING TO BATTERY: When connecting the clips to a battery, arcing is

eliminated by keeping the on-off switch in the “off” position. Connect the red battery

clamp to the positive (+) battery terminal. Connect the black battery clamp to ground:

preferably on the vehicle’s engine to a solid, metallic, stationary point. The connection

should be at least 18 inches (480mm) from the battery.

HOSE: Since the pump develops relatively low pressure, it is recommended that

non-collapsible hose be used for maximum pumping rates.

HOISTING & LOWERING: Attach a line to the metal handle on the top of the

pump for hoisting or lowering the unit. Do not use power cable for handling unit.

TO OPERATE: Lower unit into liquid to be pumped and activate switch. Pump

can be run for a few minutes without liquid, however, do not run completely dry for

extended periods. Damage to shaft seal may result.

RUNNING TIME: This unit draws about 30 amperes and can be operated

about 1hour on a fully charged 55 AMP-hour battery and still permit starting of

vehicle under normal conditions. Caution should be used when running time

exceeds 30 or 40 minutes without engine running to recharge battery, particularly

in cold weather when battery efciency is lowered. Battery size (AMP-hour rating)

and the use of other accessories such as lights and radios, etc., must be taken into

consideration for practical running periods without engine running.

OVERLOAD PROTECTION is provided by means of a 40 amp automatic reset

circuit breaker, located under top cover.

SERVICE AND OPERATING MANUAL

PortaPump

Model SPA 1½-E

Model SPA40-E

Design Level 3

Turn off before connecting

battery clamps to battery.

Arcing could result.

DANGER

IMPORTANT

Read these safety warnings

and instructions in this

manual completely, before

installation and start-up of the pump. It is

the responsibility of the purchaser to retain

this manual for reference. Failure to comply

with the recommendations stated in this

manual will damage the pump, and void

factory warranty.

DANGER

DANGER: Not for use with fluids

that have a flash point below 100°

F (38° C) [examples: gasoline, alcohol.]

Sparking could result in death.

Should unit not operate,

always check freeness

of rotation of impeller by inserting

screwdriver through hole in base

plate into slot in end of shaft.

IMPORTANT

1 2 3 4 5

Summary of Contents

Page 1 - Model SPA40-E

spa105dl3sm Model SPA1½-E and SPA40-E Design Level 3 Page 1WARREN RUPP, INC., A unit of IDEX Corporation • 800 N. Main Street • Manseld, OH 44902

Page 2 - Aux Batt

Model SPA1½-E and SPA40-E Design Level 3 Page 2 spa105dl3smTROUBLE SHOOTINGNOTE: Most common cause of failure to run is due to hardened mud and san

Page 3

spa105dl3sm Model SPA1½-E and SPA40-E Design Level 3 Page 3 ITEM TOTAL NO. PART NUMBER DESCRIPTION RQD. 1 710-004-330 Screw, Self-Tap

Page 4

Model SPA1½-E and SPA40-E Design Level 3 Page 4 spa105dl3smRepair Parts shown in bold face (darker) type are more likely to need replacement after

Page 5 - 900-001-300 Lock Washers (2)

spa105dl3sm Model SPA1½-E and SPA40-E Design Level 3 Page 5INSTRUCTIONS FOR HANDLE CONVERSION2449574828292122252627471819205515165351543031525646-4

Related models: SPA1 1/2-E

Comments to this Manuals

No comments

Sandpiper SPA40-E User Manual

Browse online or download User Manual for Pumps Sandpiper SPA40-E. SANDPIPER SPA40-E User Manual

Summary of Contents

Related models: SPA1 1/2-E

Comments to this Manuals

Related products and manuals for Pumps Sandpiper SPA40-E